Hydraulic oils
ТУ У 23.2-30802090-084:2008Lithium lubricants for rolling mills Sliding GR1 and Sliding GR2 are intended for greasing rolling work bearings of rolling mills. Lubricant Sliding GR1 is utilized in centralized systems, continuous greasing and lubricant Sliding GR2 is used as a mortgage one. The use of lubricants is permissible in roller and ball bearings units of other industrial equipment, which put forward higher requirements for mechanical and thermal stability under the influence of elevated pressures and temperatures. The lubricants are efficient at the temperature varying from minus 20°С up to 150°С.Guarantee period of storage – 3 years from the day of manufacture.Table 110
| Index name |
Sliding GR1 |
Sliding GR2 |
| Appearance |
Homogenous plastic ointment from light- brown to dark-brown colour |
| Temperature of drop falling, °С, not lower than |
250 |
260 |
| Penetration at 25°С without stirring |
290–325 |
260–290 |
| Shearing strength at 50°С, Pа, not less than |
100–420 |
140–640 |
| Efficient viscosity at minus 20°С and at the average gradient of the strain rate of 10 s−1, Pа•s, not more than |
1600 |
2000 |
| Colloid stability, %, not more than |
7 |
6 |
| Evaporation at 120°С within 1 hour, %, not more than |
3 |
| Fraction of total mass: |
|
| - mechanical impurities, insoluble HCl, % |
0,03 |
| - water, % |
0,06 |
| - free alkali re-calculated into NaOH, %, |
0,5 |
| - free organic acids,- mg КОN/g, not more than |
1 |
| Water resistance, class, not less then |
1в |
| Stability against oxidation, mg КОN/g, not more than |
3 |
| Thermal stability |
Withstands |
| Corrosive influence on metals |
Withstands |
| Tribological characteristics on ChShM at (20±5)°С: |
|
| - welding loading, N, not less than |
3283 |
| - critical loading, N, not less than |
980 |
| - scuff index, N, not less than |
440 |
| - deterioration index at loading of 196 N, mm, not more than |
0,40 | |
|
ТУ У 23.2-30802090-086:2008Rolling GR are industrial lubricants intended for centralized greasing systems of rolling mills, blast furnaces and other large equipment of metallurgical enterprises. Rolling GR S is a summer lubricant, which is used in the temperature range from 10 ° C to 80 ° C. Rolling GR W is a winter lubricant, which is used in temperatures ranging from minus 10 ° C to 80 ° C. Guarantee period of storage - 3 years from the day of manufacture.
| Index name |
Rolling GR S |
Rolling GR W |
| Appearance |
Homogeneous ointment
from light-yellow to dark-brown colour |
| Temperature of drop falling, °С, not lower than |
95 |
92 |
| Penetration at 25°С, mm•10−1 |
270–310 |
310–360 |
| Shearing strength at 50°С, Pа |
130 |
100 |
| Efficient viscosity at minus 0°С and at the average gradient of the strain rate of 10 s−1, Pа•s, not more than |
250 |
200 |
| Colloid stability, %, not more than |
10 |
12 |
| Fraction of total mass: - mechanical impurities, %- water, %- free alkali re-calculated into NaOH, %- free organic acids, mg КОN/g |
None2,00,20,8 |
| Fraction of sulphur mass,%, not less than |
0,8 |
| Corrosive influence on metals |
Withstands |
| Tribological characteristics on ChShM at (20±5)°С, N, not less than: |
|
| - welding loading, Н, not less than |
1960 |
| - critical loading ,Н, not less than |
980 |
| - scuff index, N, not less than |
400 |
- deterioration index at loading of 196 N,mm,
not more than |
0,6 | |
|
AGRINOL UNIOL-2MТУ У 23.2-30802090-087:2008Lubricants for rolling mills Agrinol Uniol-2M are used for greasing rolling mills, blast furnaces and other large equipment of metallurgical enterprises. Lubricant Agrinol Uniol-2M-1 is used for embedded parts greasing, and lubricant Agrinol Uniol-2M-2 –is utilized for greasing with the help of centralized lubrication methods. The lubricant is efficient within the temperature range:Agrinol Uniol-2M-1 - from minus 10 ° C up to 150 ° C, in a short period of time up to 170 ° C; Agrinol Uniol-2M-2 - from minus 20 ° C to 150 ° C, in a short period of time up to 170 ° C. Guarantee period of storage - 3 years from the day of manufacture.Table 103
| Index name |
Agrinol
Uniol-2M-1 |
Agrinol
Uniol-2M-2 |
| Appearance |
Homogenious ointment from light yellow to dark –brown colour |
| Temperature of drop falling, °С, not lower than |
230 |
| Penetration at 25°С, mm•10−1 |
265–320 |
320–380 |
| Proof strength, Pа, not less than |
|
|
| - at 50°С |
Not less than 200 |
100–600 |
| - at 80°С |
Not less than 200 |
80–600 |
| Efficient viscosity at minus 0°С and at the average gradient of the strain rate of 10 s−1, Pа•s, not more than |
160 |
110 |
| Colloid stability, % of the secreted oil, not more than |
9 |
12 |
| Fraction of total mass not more than: |
|
| - mechanical impurities, % |
0,1 |
| - water, % |
0,1 |
| - free alkali re-calculated into NaOH, % |
0,2 |
| - free organic acids, mg КОN/g |
0,6 |
| Corrosive influence on metals |
Withstands |
| Evaporation, %, not less than |
3 |
| Water resistance, class, not lower than |
1в |
Stability against oxidation, mg КОN/g,
not more than |
3 |
| Tribological characteristics at (20±5)°С:: |
|
| - welding loading |
2323 |
| - critical loading |
980 |
| - scuff index |
392 | |
|
ТУ У 23.2-30802090-032:2006Agrinol Termostan is a heat-resistant lubricant for heavily loaded friction units. Agrinol Termostan is used as a greasing material for frictionless bearings of average and low speed and other friction units exploited at elevated temperature and loading (rolling mill rolls, founding equipment, calcinators and thermal furnaces etc.)The lubricant is efficient within the temperature range from minus 20°С up to 230°С. It remains efficient at the temperature not higher than 250°С in a short-term period. It also can be used in a short-term period at the temperature not higher than 280°С if the unit is hermetic.The lubricant contains mineral anti-friction additives which possess good adhesion to metal and make the lubricant efficient at the temperature exceeding that of drop falling. The lubricant should be placed into friction units in a manual way with the help of the method of laying or by greasing attrition faces.Guarantee period of storage - 3 years from the day of manufacture.
| Index Name |
Agrinol Termostan |
| Appearance |
Homogenous plastic ointment of black colour |
| Temperature of drop falling, °С, not lower than |
260 |
| Penetration at 25°С, mm•10−1 |
250–300 |
| Efficient viscosity at 0°С and at the average gradient of the strain rate of 10 s−1, Pа•s, not more than |
1500 |
| Shearing strength at 50°С, Pа, not less than |
300 |
| Colloid stability, %, not more than |
5 |
| Fraction of total mass of free alkali re-calculated into NaOH, %, not more than |
0,2 |
| Evaporation, %, not more than |
5 |
| Corrosive influence on metals |
Withstands |
| Water resistance, class, not lower than |
1v |
| Stability against oxidation, mg КОN/g, not more than |
3 |
| Tribological characteristics on ChShM at (20±5)°С: |
|
| - welding loading, N, not less than |
6174 |
| - critical loading, N, not less than |
980 |
| - scuff index, N, not less than |
750 |
| - deterioration index at loading of 392 N, mm, not more than |
0,7 | |
|
ТУ У 23.2-30802090-033:2006Rolling KLS-1and Rolling KLS-2 are complex lithium lubricants for rolling mills. These lubricants are utilized for greasing frictionless bearings of rolling mill working rolls. Rolling KLS-1 is used in centralized systems of continuous greasing, and Rolling KLS-2 is used as a layed lubricant. It is permitted to utilize the lubricants for roller and ball bearings of units of other industrial equipment which should correspond to the high standards of mechanical and thermal stability under the influence of increased loading and temperature. The lubricants are efficient at the temperature varying from minus 20°С up to 150°С.Guarantee period of storage - 3 years from the day of manufacture.
| Index Name |
Rolling KLS-1 |
Rolling KLS-2 |
| Appearance |
Smooth plastic ointment from light-brown to dark-brown colour |
| Temperature of drop falling, °С, not lower than |
250 |
260 |
| Penetration at 25°С, mm•10−1 |
290–325 |
260–290 |
| Proof strength at 50°С, Pа |
100–420 |
140–640 |
| Efficient viscosity at minus 20°С and at the average gradient of the strain rate of 10 s−1, Pа•s, not more than |
1600 |
2000 |
| Colloid stability, % of the secreted oil, not more than |
7 |
6 |
| Evaporation at 120°С within 1 h, %, not more than |
3 |
3 |
| Water resistance, class, not lower than |
1v |
1v |
| Fraction of total mass, not more than: |
|
|
| - mechanical impurities, % |
0,03 |
0,03 |
| - water, % |
0,06 |
0,06 |
| - free alkali re-calculated into NaOH, % |
0,5 |
0,5 |
| - free organic acids, mg КОN/g |
1 |
1 |
| Corrosive influence on metals |
Withstands |
| Thermal stability |
Withstands |
| Tribological characteristics at (20±5)°С: |
|
|
| - welding loading, N, not less than |
3283 |
3283 |
| - critical loading, N, not less than |
980 |
980 |
| - scuff index, N, not less than |
440 |
440 |
- deterioration index at loading of 196 N, mm,
not more than |
0,40 |
0,40 | |
|
| |
|
